Secure Communications Group

Commercial Alarm and Intrusion Detection

A commercial intrusion system detects a person inside a protected area and delivers that event to someone who can act. Sensors, panel and signaling are only as good as their placement and verification. Most systems fail through nuisance activations people learn to ignore, not through defeated hardware.

An alarm that trips on a draft is worse than no alarm, because it teaches everyone to dismiss the next event. Commercial intrusion work is therefore less about catalog features and more about where each sensor sits, how activation is confirmed, and which path the signal takes when the internet connection is gone.

We design in layers, starting at the building envelope and working inward to the rooms that hold cash, records, keys, medication or tools.

Based in Westminster. Serving Denver and clients across Colorado. See all Colorado service areas.

Dahua security camera installed on a commercial building
A commercial camera installation. The camera, mount and cable route are chosen for the surface and the view.

Perimeter first, interior second

The envelope is the cheapest place to detect someone and the easiest place to generate false alarms if it is treated carelessly. Recessed contacts suit finished office doors. Surface contacts with armored cable suit warehouse overhead doors and gates that flex. A contact that no longer lines up, because a door has sagged or a latch has worn, reports a fault that reads as an intrusion.

Glass break detectors listen for the pattern of breaking glass and belong near the pane they protect, not across the room. Shock sensors on a door or wall detect forced entry through the surface itself. Both complement contacts rather than replacing them.

  • Door and window contacts on the envelope, chosen for the frame and its movement.
  • Glass break or shock detection wherever the glazing is reachable.
  • Interior motion covering the paths between the envelope and the valuables.

Choosing sensors that hold up

Passive infrared sensors see heat in motion, so they can miss someone moving toward them and can be confused by a warm surface that changes. Dual-technology sensors require both infrared and microwave, cost more, and resist the conditions that make a single technology cry wolf: sunlight through a window, a radiant heater, air from a rooftop unit.

Mounting height, angle and what the sensor can see from that position decide performance more than the model number. A sensor pointed down an aisle between racking works. The same sensor pointed at a loading door that opens onto a bright yard will not.

  • Beam detectors along aisles and in long rooms where an area sensor cannot cover the distance.
  • Curtain sensors for skylights, overhead doors and glass walls.
  • Sensors kept away from vents, heaters and moving machinery.
  • Wireless sensors only where cabling is impractical, and only after checking the radio path.

Partitions, schedules and who arms what

A partition is an area that arms and disarms independently, which lets one tenant arm a suite while the shared corridor stays disarmed. Most sites need a perimeter and an interior partition, plus separate areas for a pharmacy, a server room or a cash counter.

Schedules and opening reports are where the system earns its keep. Auto-arm at a set time, auto-disarm at opening, and a record of who disarmed and when turn the panel into a tool for managing the building rather than a box on a wall.

  • Partitions that match how the site is actually occupied.
  • Arming by keypad, credential or app, with permissions per person.
  • Opening and closing reports delivered to the people who act on them.

Getting the signal out reliably

The alarm is only useful if the message leaves the building. A single internet path fails when the carrier connection fails, and a single phone line fails when the line is cut before entry. Dual-path signaling, usually IP with a cellular radio backup, gives the panel a second route and shows the receiving station that it is still alive.

Notification design matters as much as transport. A system that texts ten people creates ten who each assume someone else responded. We agree who receives what, and what happens when nobody acknowledges.

  • Notification lists with named responsibility rather than a group text.

The causes of commercial false alarms

Almost every nuisance activation traces to a short list: a door that no longer closes squarely, a motion sensor seeing an HVAC vent or a patch of afternoon sun, insects in a sensor housing, a wireless sensor at the edge of radio range, or an interior partition armed while people are still working.

Those causes are findable. We walk test every zone, record which zone triggers over the first weeks, and correct the placement or the hardware rather than asking staff to live with the noise.

  • A documented walk test of every zone before handover.
  • A check of activations after the first month of real activity.
  • Door hardware corrected rather than the detector desensitized.
  • Staff shown which partition to arm at the end of the day.

Alarms, cameras and access control together

When an alarm event arrives with video attached, the person receiving it can decide in seconds whether it is real. Linking a sensor zone to a camera preset turns the right camera to the right view when the zone trips, and an access control event can tell the alarm system a door was forced or held.

That linkage is worth building only if the underlying systems are healthy. A camera aimed at a wall and a sensor aimed at a heater produce an integration that fails faster, not better.

Related:Commercial security servicesIntegrated security systemsAlarm inputAlarm annunciatorsAlarm system installation in Colorado

Frequently asked questions

Will pets set off a commercial alarm?

Pet-immune sensors are rated by the weight and height of the animal they ignore, and they work by excluding the lower part of the view. A determined animal still finds a way, so placement and the routes an animal actually uses matter more than the label on the box.

Can the alarm report without a phone line?

Yes. An IP path with a cellular radio backup is the usual design, and it removes the dependence on a landline that can be cut outside the building. The panel and its communicator still need battery backup to carry the system through a short outage.

How do we reduce false alarms?

Fix the causes rather than the sensitivity. Correct the door that no longer latches, move the sensor that sees a vent, replace the wireless device at the edge of range and confirm arming habits with staff. A zone-by-zone check after the first month finds most of it.

Do we need a new alarm panel?

Only if the existing panel cannot carry the zones, partitions or signaling the site needs. Panels in service that still hold their programming and support a backup communicator are often extended rather than replaced, and we test that before recommending a change.

Ready to plan your security system?

Tell us what you need to protect and we will scope the cameras, access control or alarms that fit. We work across Denver and across Colorado.

Office hours:
Mon–Thu 9:00am–5:00pm · Fri 9:00am–4:00pm · Closed Saturday and Sunday

Call or send a quote request

Call the office or send a quote request with the site, the areas you need covered and any existing equipment you want to keep.